Monday, September 15, 2014

A New Pedaling Technique?

This post expands on many of the points covered in my video, "An Introduction to Double Pedaling."

Over the past two months, I have been developing “double pedaling,” a pedaling technique that allows the damper and sostenuto pedals to be used together in new ways. The sostenuto pedal, patented by Albert Steinway in 1874, remains little more than a curiosity among today’s pianists—even many experienced pianists have only a hazy idea of the potential applications of this pedal. Double pedaling greatly increases the possibilities of the sostenuto pedal, giving pianists unprecedented control over the resonance of their instrument. The pedal mechanism on the modern piano has a crucial flaw that prevents or complicates double pedaling in all but the most trivial instances. Fortunately, this flaw is easily fixed with a slight modification.

The Sostenuto Mechanism

The sostenuto pedal is like a selective damper pedal. The actual damper pedal (the right pedal) lifts all the dampers, the sostenuto pedal only holds up the dampers of the notes that are being played when it’s pressed.



The picture above shows the damper lift rods of a grand piano. The sostenuto mechanism consists of two elements: the sostenuto rod (a metal bar that runs lengthwise next to the damper mechanism), and sostenuto tabs (covered in red felt in the above picture, each damper lift rod has a tab attached). When a damper is lifted, the corresponding sostenuto tab goes up with the rest of the mechanism. When the sostenuto pedal is depressed, the sostenuto rod moves into the path of the tabs, preventing the raised tabs from going back down and holding the raised dampers up.



The picture above was taken with the sostenuto pedal depressed. The sostenuto rod has moved into position and has caught two sostenuto tabs, preventing the corresponding dampers from descending.

The dampers that are down when the sostenuto pedal is engaged won’t be held up, because their sostenuto tabs are under the sostenuto rod. Those dampers will still go up when the corresponding keys are pressed, but their sostenuto tabs will remain underneath the sostenuto rod. To facilitate the normal action of these dampers, the sostenuto tabs are attached to the damper mechanism with a hinge so that they can bend downwards, as in the picture below.





The Problem with the Sostenuto Pedal

This brief discussion of the sostenuto mechanism demonstrates why the sostenuto pedal does what it does: it holds up any dampers that are raised when it is depressed. It’s worth taking a step back, though, and asking the question, what should the sostenuto pedal do? My answer: the sostenuto pedal should hold up only the dampers that correspond to piano keys that are being played.

There is a small but crucial difference between what a sostenuto pedal does and what it should do. As long as the damper pedal doesn’t enter the picture, the sostenuto pedal works correctly—dampers are only raised when the corresponding keys are being played. However, the damper pedal lifts all the dampers, rendering the sostenuto pedal useless! If the sostenuto pedal is pressed while the damper pedal is down, all the dampers will be caught in the raised position, regardless of which keys are being played at the time. While this seems like a small issue, it completely undermines the usefulness of the sostenuto pedal. Classical pianists today use the damper pedal almost all the time in music from Beethoven to the present. As a result, the sostenuto pedal can only be used in unusual situations, and it requires special care so that the damper pedal doesn’t screw it up.

In order to reap the full benefits of double pedaling, it’s necessary to modify the mechanism so that the damper pedal doesn’t interfere with the sostenuto mechanism—in other words, the sostenuto pedal will function as it should, even when the damper pedal is depressed. We can then catch notes or chords on the sostenuto pedal while the damper pedal is down.


The Solution

The problem boils down to the fact that playing notes on the keyboard and pressing the damper pedal are equivalent as far as the damper action is concerned. In both cases, the dampers are raised in the same way, to the same height. The key to solving our double pedaling problem is to restrict the damper pedal so that it raises the dampers to a slightly lower level.

Experienced pianists know that pedaling is not really a binary thing. There’s the “black and white” of pedal up and pedal down, but there’s also an infinity of grays in between. This “half-pedal” zone can be tested by depressing the pedal very slowly and continuously testing the piano’s resonance. Half-pedal is a deceptive term, as it’s actually much closer to the “up” pedal position. At the position we call “half-pedal” (or quarter-pedal, or three quarters-pedal) the pedal is barely depressed, and the dampers are barely raised off the strings, muting them to some degree. Once the pedal has been depressed further, to about half or three quarters of the way down, the dampers are already fully off the strings and the piano sounds exactly like it does at full pedal. A fully-depressed pedal lifts the dampers an extra few millimeters, but doesn’t actually change the sound of the instrument. However, these millimeters are crucial, because the damper needs to be lifted all the way in order to be caught be the sostenuto pedal.




I’ve illustrated this in the diagram above. The “sweet spot” refers to the point in the damper’s upward trajectory where the dampers are fully off the string, but are not yet high enough to be caught by the sostenuto pedal. Restricting the damper pedal’s range so that it can’t go past the sweet spot will prevent the damper pedal from interfering with the sostenuto pedal. Pressing a key on the keyboard will still lift the damper all the way.

On most pianos, restricting the damper pedal is a simple operation that only takes a few minutes. There is usually a screw that is attached to the bottom of the body of the piano, above the damper pedal rod. Adjusting the screw is one solution (see the picture below).



For a quick fix, or for pianos without an adjustable screw, there are various points in the pedal action where a barrier can be added to restrict the pedal motion. In the picture below, I added a folded piece of paper at the top of the pedal lyre.




Troubleshooting a restricted pedal

Restricting the damper pedal should allow double pedaling on any well-regulated instrument. Unfortunately, many instruments, even carefully maintained concert instruments, have issues with the sostenuto mechanism that are ignored because the sostenuto pedal is so rarely used. The adjustments suggested below can be attempted if restricting the damper pedal doesn’t produce the desired results, and should only be carried out by a trained piano technician.

The most common problem is that the sostenuto rod is not in the correct position and catches dampers that are barely raised. The diagram below shows how a faulty sostenuto mechanism can cause instruments to have no sweet spot at all.



This can be solved by adjusting the sostenuto rod so that it catches the tabs in a higher position.

Sometimes the sostenuto pedal is not consistent, catching some notes but not others. This happens when the dampers are lifted unevenly. Regulating the dampers is a major operation that can take several hours. Depending on how severity of the problem, adjusting the sostenuto rod instead may be a more cost-effective solution. For the purposes of double pedaling, it’s advantageous to have the dampers lift further off the string, which increases the size of the sweet spot. However, too much lift can affect their ability to dampen the strings promptly on release of a key, since only the force of gravity returns the dampers to the rest position!

Another common problem occurs when notes are caught on the sostenuto pedal after the pedal is depressed. Sometimes the hinge on the sostenuto tab does not work correctly, so that the tab “jumps” over the engaged sostenuto bar instead of flexing down. This may require adjusting or replacing the faulty tabs.

Double Pedaling Techniques

Once you’ve “liberated” the sostenuto pedal from the damper pedal, you’re ready to explore all the possibilities of double pedaling. I’ve found four basic double pedaling techniques:

1. Joint Pedaling

In joint pedaling, the sostenuto pedal catches part of a larger sonority (usually including a bass note). The damper pedal is then used normally, but with the advantage that the pedal can be changed without losing the sonority. Most double pedaling applications in the standard repertoire fall under this category.




In the above passage from “Ondine” from Gaspard de la nuit by Ravel, it’s impossible to achieve a legato bass line as marked without double pedaling. Holding the C sharp with the damper pedal blurs the change of harmony on the second beat. By catching the C sharp with the sostenuto pedal, the damper pedal can be changed on the second beat without losing the bass.

This would normally require the pianist to keep the damper pedal raised while the sostenuto pedal is depressed, creating a gap in the sonority that undermines the sensual sweep of the right hand arpeggio. Restricting the damper pedal solves this problem!

2. “Only Hands Small” Technique

Do you have small hands but big ideas? Pianists with smaller hands often have to break chords or release notes early, and are left with the dilemma of either losing the full sonority or muddying the pedal. By catching some notes with the sostenuto pedal immediately before a damper pedal change, it’s possible to overcome this disadvantage. Here’s an illustrative passage from the Piano Concerto No. 2, Op. 44 by Tchaikovsky:




My left hand isn’t big enough to hold the bass D in the final rolled chord. That means that I need to change my pedal early in the roll (before the F sharp) to catch the bass D.



This solution is not ideal, since it makes it impossible to preserve a legato connection between the melody D in the right hand and the preceding E. A better solution is to catch the bass D with the sostenuto pedal, allowing me to change the damper pedal at the melody note without losing the bass.



It is important to release the E octave in the right hand (shown in the full except above) before beginning the roll; otherwise it will be caught on the sostenuto pedal and will blur the D major chord. The E will still be held on the damper pedal.

3. Overlapping Technique
Overlapping the damper and sostenuto pedal can produce all kinds of highly complex sonorities. The current piano repertoire doesn’t offer too many opportunities for interesting overlapping effects. This is an area that I hope will be explored soon by budding composers.

Here’s one example of overlapping technique, from the Piano Concerto No. 3, Op. 30 by Rachmaninoff. This passage alternates between two chordal melodies moving in different directions. While Rachmaninoff doesn’t indicate it, you can get an interesting effect by sustaining each melody while the other melody is active, for a true contrapuntal texture.

Here is the conventional pedaling approach:



Most recordings use this pedaling, or something similar. This pedaling sustains both melodies equally. However, you can still hear an eighth-note gap in one of the melodies at each pedal change (shown with big red rests):



Theoretically, double pedaling lets you play both melodies legato, without any gaps. On each beat of each measure, first change the damper pedal and then change the sostenuto pedal:



It works as follows: on the first beat, the damper pedal goes down, and then the sostenuto pedal catches the chord from the upper melody. On the second beat, the sostenuto pedal holds the upper melody while the damper pedal changes, and then changing the sostenuto pedal catches the lower melody. On the third beat, the sostenuto pedal holds the lower melody while the damper pedal changes, and then changing the sostenuto pedal catches the upper melody! And so on. This pedaling looks intriguing on paper, but in practice I found it too cumbersome at tempo. Still, it shows some of the vast potential of the overlapping technique.

4. The Partial Sostenuto
Double pedaling enables catching part of a chord on the sostenuto pedal. That’s impossible with conventional pedaling, at least without releasing the extra notes. The “partial sostenuto” technique is useful in this passage from the Etude-tableau Op. 39, No. 7 by Rachmaninoff:



With double pedaling, I can catch the first chord in the left hand of this example without catching the right hand notes. First, I play the chord and depress the damper pedal. I can then lift my right hand and the pedal will keep the melody ringing. Since I am no longer holding down the right hand notes, they won’t be caught when I press the sostenuto pedal to catch the left hand chord.

Conclusion

I have only begun experimenting with double pedaling technique over the course of the past few months, and I am already convinced that it is a powerful tool that has wide-ranging potential to enhance the coloristic and expressive capabilities of the modern instrument, with numerous possible applications in the standard piano repertoire. Modifying the pedal mechanism to allow double pedaling is a simple operation that can be achieved without any additional piano parts—only minor adjustments are necessary.

My goals with my double pedaling project are as follows:

1) To increase awareness of the sostenuto pedal’s function and its applications, and to develop and spread the practice of double pedaling.

2) To make a working sostenuto pedal a standard part of every instrument. Many entry-level grand pianos still do not have sostenuto pedals, and it is rare to encounter an upright piano with a sostenuto pedal (Steinway uprights, select Bösendorfers and the Yamaha YUS series are the exceptions). Of course, having a sostenuto pedal on a piano does not mean that it will actual work, as keeping it regulated is frequently seen as optional!

3) To encourage piano makers to modify their pedal mechanisms in house, so that double pedaling works correctly on new pianos without any further modifications.

I’m optimistic that I’ll see some real progress in these areas in the near future. Unfortunately, I don’t anticipate it will be a smooth road. The current environment in the piano world is very hostile to any innovation in piano design. So I’m asking for your participation! I would love to hear any feedback on double pedaling, or any new pedaling ideas that you might have. Also, please share this article and my video on double pedaling, which is available here: http://youtu.be/AWEFgQyCRok

Thanks!

As a final note, there is one type of piano that consistently has a working sostenuto pedal: electronic pianos. On most full size modern keyboards, it’s simple and cost-effective to buy a pedal board with a sostenuto pedal, if it’s not already included. Due to a quirk in the way that keyboards are programmed, it is slightly easier to have a sostenuto pedal that works independently of the damper pedal than the alternative. It’s not surprising that keyboard manufacturers have taken the path of least resistance and have developed a sostenuto pedal that works perfectly for the purposes of double pedaling.

Happy pedaling!

3 comments:

  1. Highly Appreciated, I will provide feed back when tested. Actually on old Steinway, not the easiest sostenuto to manage; ;)
    Thanks

    ReplyDelete
  2. An interesting concept, and I agree that it can have its application. However, from a technical standpoint, adjust the pedal in that way negatively affects the touch of the piano, and quite dramatically. Stopping the damper pedal’s travel before the key travel results in the keys hitting the underlevers near the bottom of the keystroke. This ends up near the point of let-off, and makes playing softly difficult. The extra resistance added right at the end of the hammer travel can cause a pianist to miss notes intended to be played pianissimo. Have you worked with or developed the concept any further? Interested to hear your thoughts/progress.

    ReplyDelete
    Replies
    1. Hello, thanks for your thoughts. I hadn't noticed any difference in the action, and now I'll definitely have to think this through!

      Though, I'm surprised that you found it difficult to play softly with a restricted damper pedal. It's true that you might encounter more resistance when you play very softly with the pedal down, but I would think that would happen after the hammer has already left the escapement?

      In terms of real measurements, you need loose dampers to make this technique work (about 6-8 mm as opposed to the 4-5 mm on a new set of dampers) so the difference in damper travel is only a few millimeters right at the bottom of the keystroke. I'll definitely need to test the limitations on the touch in this way!

      IMO the best way to develop this further would actually be to change the sostenuto mechanism slightly to make it independent of the damper pedal. There are lots of ways to do this, but in light of your comment I wonder how they would impact the action for better or worse.

      Delete